Search found 47 matches

by rodneyp
August 30th, 2017, 6:17 am
Forum: Installation
Topic: "Unable to Install the system" Core 112
Replies: 17
Views: 656

Re: "Unable to Install the system" Core 112

It transpired that there were two problems Faulty RAM - the machine reported "segmentation faults" when I moved a pre-installed HDD to it and booted. memtest86 reported only two faulty bits, but that was sufficient to bomb the installer. After I removed the faulty RAM module (that I had marked as te...
by rodneyp
August 20th, 2017, 10:58 pm
Forum: Installation
Topic: ipFire Installation failure
Replies: 5
Views: 353

Re: ipFire Installation failure

I've had identical problem with cores 111 & 112. Although it does not resolve the issue, a work-around that does work and could be adequate for your use as a reserve IPFire box, is to install the flash image for i586, http://downloads.ipfire.org/releases/ipfire-2.x/2.19-core112/ipfire-2.19.1gb-ext4....
by rodneyp
August 20th, 2017, 10:52 pm
Forum: Installation
Topic: "Unable to Install the system" Core 112
Replies: 17
Views: 656

Re: "Unable to Install the system" Core 112

Now looking like this is a continuation of the problem reported for core 111 in http://forum.ipfire.org/viewtopic.php?f=51&t=19091 The problem has now been reported for 3 quite different hardwares - FWIW mine is an ASUS A6U. Partitioning appears to complete and /boot gets partially installed before ...
by rodneyp
August 20th, 2017, 7:50 am
Forum: Installation
Topic: "Unable to Install the system" Core 112
Replies: 17
Views: 656

Re: "Unable to Install the system" Core 112

I've now tried a fresh install of core 112 to a different HDD and got your result - "unable to install system" parted might be the faulty program. Console 2 shows it being instucted to produce partitions optimally aligned for 4k logical sectors - but it doesn't. It does throw a warning (twice) that ...
by rodneyp
August 18th, 2017, 11:11 pm
Forum: Installation
Topic: "Unable to Install the system" Core 112
Replies: 17
Views: 656

Re: "Unable to Install the system" Core 112

Its a while since I purchased new HDD. The WD, IIRC, came unformatted from the factory. Those having "PVR" suffix are advanced format and likely to have GPT, if any partition table. Zeroing out the MBR would not suffice because GPT partition table occupys sectors 1 to at least 33. Nevertheless, if y...
by rodneyp
August 18th, 2017, 4:10 am
Forum: Installation
Topic: "Unable to Install the system" Core 112
Replies: 17
Views: 656

Re: "Unable to Install the system" Core 112

The hardware you are using certainly looks useful for IPFire. It would be worthwhile resolving the issue. It's not clear whether your HDD was new or came with Windows pre-installed. Do you recall whether or not GPT partition table was present ? IPFire installer would replace that with MSDOS partitio...
by rodneyp
August 17th, 2017, 4:56 am
Forum: Installation
Topic: "Unable to Install the system" Core 112
Replies: 17
Views: 656

Re: "Unable to Install the system" Core 112

Your earlier comment about boot mode applying only after first reboot might not be entirely correct. ISO that are not built for UEFI won't boot from it. You could try booting an IPFire flash image from a USB device UEFI is continually changing and your two examples of the mainboard might have differ...
by rodneyp
August 11th, 2017, 11:30 pm
Forum: Installation
Topic: "Unable to Install the system" Core 112
Replies: 17
Views: 656

Re: "Unable to Install the system" Core 112

Would you be specific about the brand and model of mini-pc. That would serve two purposes prompt any other IPFire users of the same model to assist caution others not to obtain the same kit and expect it to work with IPFire unless/until the issue is resolved Is the PC primarily UEFI and if so, have ...
by rodneyp
August 5th, 2017, 8:58 am
Forum: Installation
Topic: Installing IPFire in my existing Network
Replies: 2
Views: 253

Re: Installing IPFire in my existing Network

Hi Odania, When I was administering a network of about 20 PC, I connected the IPFire RED to modem/router (distribution switch in your case) and IPFire GREEN to access switch. I moved the Domain Controller to same access switch as users. I also disabled DHCP on Domain Controller, because it was less ...
by rodneyp
August 3rd, 2017, 12:09 pm
Forum: IPFire in General
Topic: wrong time?
Replies: 7
Views: 256

Re: wrong time?

If you can't resolve the issue then you could disable IPFire providing time to the LAN. Win10 should then get it direct from a time server on the Internet. If it is still wrong then the problem would appear to lie in Win10
by rodneyp
August 2nd, 2017, 11:24 am
Forum: IPFire in General
Topic: wrong time?
Replies: 7
Views: 256

Re: wrong time?

It sounds like you're setting the PC in Win10. You need to set current UTC time in PC hardware settings (CMOS) then +GMT10 in Win10.

ditto for the IPFire box.

also need to ensure that IPFire is providing time to machines on its network. Go to the services tab and "time setting"
by rodneyp
August 1st, 2017, 10:01 pm
Forum: IPFire in General
Topic: wrong time?
Replies: 7
Views: 256

Re: wrong time?

You don't say which Au time zone you are in. The time difference is 9 hrs, and West Australian time is 9 hrs ahead of UTC. Windows sets the hardware clock to local time - the time utility is likely to add the timezone difference to that. If you want correct time to display then you would need to set...
by rodneyp
August 1st, 2017, 12:55 am
Forum: Addons
Topic: Libvirt with disk access
Replies: 2
Views: 152

Re: Libvirt with disk access

It depends on what you mean by "physical disk". If you were to partition the disk to a single large partition and format it to (say) xfs, or failing that ext4, you could then amend /etc/fstab to mount the partition to /var/lib/libvirt/images. libvirt works that way on my desktop machine although I d...
by rodneyp
May 22nd, 2017, 5:49 am
Forum: Installation
Topic: Client can only connect through green red bridge - noob first install
Replies: 1
Views: 434

Re: Client can only connect through green red bridge - noob first install

You have the modem in the same numbered network, 192.168.178.0, as GREEN, which is incorrect. I would anticipate a modem in passthrough (bridging) mode to not have an IP address at all. That would be the most reliable change. Using the modem to provide DHCP for the LAN won't work, when IPFire is in ...
by rodneyp
May 16th, 2017, 6:03 am
Forum: IPFire in General
Topic: Can't connect ipfire web interface [SOLVED]
Replies: 6
Views: 524

Re: Can't connect ipfire web interface

You don't say which IPFire compilation you are using and whether or not you are using DHCP.

With an ARM compilation, I find that the modem has to be finished booting, before the IPFire is booted and so on in the chain of devices.