Search found 6618 matches

Go to advanced search

by Arne.F
February 20th, 2017, 10:52 pm
Forum: IPFire in General
Topic: Backup - Generate ISO generates 3 files?
Replies: 2
Views: 49

Re: Backup - Generate ISO generates 3 files?

The three files are normal. The 166mb is the official installimage and the ipf is the backup of your system. The large iso is build from this files and can used to reinstall and restore the backup.
by Arne.F
February 10th, 2017, 12:02 pm
Forum: Problemlösungen
Topic: Reconnect an Kabelmodem bei Wechsel IPFire
Replies: 4
Views: 105

Re: Reconnect an Kabelmodem bei Wechsel IPFire

Bei den meisten Providern bekommt nach dem Neustart des Modems die erste DHCP anfragende Netzwerkkarte die IP. Alle anderen werden verworfen. Wenn du also auf den anderen IPFire switchen willst ohne das Modem neu zu starten müssen beide IPFires auf red die gleiche MAC Addresse haben. (Wichtig! auf k...
by Arne.F
February 9th, 2017, 1:33 pm
Forum: Konfiguration
Topic: [gelöst] DNS-Auflösung für den ipfire funktioniert nicht
Replies: 21
Views: 481

Re: DNS-Auflösung für den ipfire funktioniert nicht

Der Eintrag "local recursor" ist der Hinweis, dass öffentliche IP-Adressen nicht korrekt (DNSSec validierend) aufgelöst werden. Das ist nicht so ganz richtig. Der Hinweis "local recursor" bedeutet das die im IPFire konfigurierten oder vom ISP gesetzten Nameserver nicht korrekt a...
by Arne.F
February 7th, 2017, 10:29 am
Forum: Entwicklung
Topic: Kabelanschluss ip wird nicht mehr geändert
Replies: 8
Views: 342

Re: Kabelanschluss ip wird nicht mehr geändert

Ich denke mal manche Dyndns Provider meckern wenn sich die IP innerhalb von einem gewissen Zeitraum nicht aendert.. Bei den meisten Providern muss man alle 30 Tage ein Update machen auch wenn sich die IP nicht geändert hat, aber nicht öfter. (holdoff_days=30) Der Dyndns client im IPFire sollte das ...
by Arne.F
February 6th, 2017, 3:22 pm
Forum: Hardware
Topic: Wireless 3160 / iwlwifi-3160-16.ucode
Replies: 5
Views: 351

Re: Wireless 3160 / iwlwifi-3160-16.ucode

5ghz auf neueren Intel karten kannst du vergessen. Das ist in der Hardware geperrt. (Region Lock auf 00-World) Solange die Hersteller die Karten nicht auf Zielland im EEProm einstellen geht der AP Mode nur auf Kanel 1-11. Bisher gibt es leider dank FCC keine tools mit denen der User das selbst umst...
by Arne.F
February 6th, 2017, 6:23 am
Forum: Konfiguration
Topic: Script nach Aufbau der (PPPoE) Verbindung
Replies: 4
Views: 71

Re: Script nach Aufbau der (PPPoE) Verbindung

Du musst den Aufruf in /etc/sysconfig/firewall.local in die start Section packen damit er nach jeder Neueinwahl aufgerufen wird.
by Arne.F
February 5th, 2017, 11:10 pm
Forum: IPFire in General
Topic: Double SubDir (Case Sensitive)
Replies: 3
Views: 109

Re: Double SubDir (Case Sensitive)

It is correct that there are E and e (Eterm is Eterm with xterm style color support and eterm is gnu emacs term)

Linux/Unix filesystems are case sensitive. To made a correct backup you have to use a tool like tar that can handle this.
by Arne.F
January 20th, 2017, 8:10 am
Forum: Installation
Topic: eMMC Installation: No Disk Found
Replies: 11
Views: 300

Re: eMMC Installation: No Disk Found

The 64bit nightly was now finished the i586 is still building ...
http://nightly.ipfire.org/next/2017-01- ... -ba957627/
by Arne.F
January 20th, 2017, 8:05 am
Forum: IPFire in General
Topic: new compulab fanless pc2
Replies: 3
Views: 166

Re: new compulab fanless pc2

Intel 211 is also on the 2GB versions of the APU2 and should work. Intel 219 is a phy (Physical Layer), the main controller is in the SoC but i have no info about the state in IPFire. The info that a device is listed in the fireinfo doesn't say if it is supported. Fireinfo only read the PCI id's and...
by Arne.F
January 19th, 2017, 3:10 pm
Forum: Installation
Topic: eMMC Installation: No Disk Found
Replies: 11
Views: 300

Re: eMMC Installation: No Disk Found

Arrrg. The same problem with newer CSD version. In actual kernel releases the entire CSD Version check is removed...

I will patch the kernel next days...
by Arne.F
January 19th, 2017, 3:45 am
Forum: Installation
Topic: eMMC Installation: No Disk Found
Replies: 11
Views: 300

Re: eMMC Installation: No Disk Found

Switch to 2nd console and check the messages. You can also execute dmesg here to get the kernel log. But its not so easy to get the logfile out because the installer run in a ramdisk.
Maybee it is easier to boot a Flash image from an usb stick to check if the eMMC was detected.
by Arne.F
January 19th, 2017, 2:37 am
Forum: Installation
Topic: eMMC Installation: No Disk Found
Replies: 11
Views: 300

Re: eMMC Installation: No Disk Found

The eMMC version 5.0 problem should be fixed long time ago. Do you really get the same csd version 7 error ?
by Arne.F
January 19th, 2017, 2:25 am
Forum: IPFire in General
Topic: blacklist and https wpad
Replies: 3
Views: 198

Re: blacklist and https

No. Transparent mode means that port80 (http) is redirected to the proxy via a firewall rule. It can only work for http because the requests are not encrypted. The traffic on port 443 cannot redirected with this method because the ssh handshake will fail. Https can only filtered if the proxy was con...
by Arne.F
January 18th, 2017, 3:59 pm
Forum: IPFire in General
Topic: Explanation connection overview
Replies: 3
Views: 93

Re: Explanation connection overview

The aplication layer gateway is not the reason, the reason is the IP masquerade you your lan networks behind one public IPv4 address. The fist sip devices can establish a connection via 5060, but if a second device or provider cannot use incoming 5060 again so ipfire has to switch to an other extern...
by Arne.F
January 18th, 2017, 12:30 pm
Forum: Problemlösungen
Topic: Mehrere Homepages nicht erreichbar
Replies: 42
Views: 690

Re: Mehere Homepages nicht erreichbar

Have you enabled p2p filters? They sometimes has false positives because the p2p packets are very similar to normal webdownloads.

Go to advanced search