Page 2 of 2

Re: Problems update Guardian 2.0.2

Posted: December 30th, 2018, 3:25 pm
by Mentalic
Think I found the fix to this. After many uninstalls reinstalls, service stop and starts with no success in getting guardian working again.. Until in Guardian Configuration interface, I set "monitor snort alert file" to OFF, then save setting, then set "monitor snort alert file" to ON and save setting. Been working ever since.

Initially when I did the packfire update from 125 to 126 Guardian worked, but later clean installs of IPfire all resulted in guardian not working. Something wrong somewhere. ;)

Re: Problems update Guardian 2.0.2

Posted: December 30th, 2018, 5:18 pm
by Roberto Peña
YES, It´s works OK.

Thanks Mentalic for this!!!. O0

When Bugzilla works (it looks like it is down), I report it.

Greetings.

Re: Problems update Guardian 2.0.2

Posted: December 30th, 2018, 9:52 pm
by Deepcuts
Mentalic wrote:
December 30th, 2018, 3:25 pm
Think I found the fix to this. After many uninstalls reinstalls, service stop and starts with no success in getting guardian working again.. Until in Guardian Configuration interface, I set "monitor snort alert file" to OFF, then save setting, then set "monitor snort alert file" to ON and save setting. Been working ever since.

Initially when I did the packfire update from 125 to 126 Guardian worked, but later clean installs of IPfire all resulted in guardian not working. Something wrong somewhere. ;)
Indeed, this is a bug in 126.
This fix works for me.

Re: Problems update Guardian 2.0.2

Posted: December 30th, 2018, 11:09 pm
by JonM
Mentalic wrote:
December 30th, 2018, 3:25 pm
Think I found the fix to this. After many uninstalls reinstalls, service stop and starts with no success in getting guardian working again.. Until in Guardian Configuration interface, I set "monitor snort alert file" to OFF, then save setting, then set "monitor snort alert file" to ON and save setting. Been working ever since.
This worked for me also! Thank you Mentalic! ;D

Re: Problems update Guardian 2.0.2

Posted: December 31st, 2018, 8:58 am
by qiller
Worked 4 me too, but after a reboot i got the same problem again. Perhaps a timing problem with certain configurations?

Re: Problems update Guardian 2.0.2

Posted: December 31st, 2018, 12:27 pm
by Deepcuts
Today my IPFIre crashed hard for some reason.
I had to reinstall from scratch.
After enabling IDS on red, selecting some rules and clicking save, the rules setup is not saved. I guess this goes deeper than just Guardian.
Using sourcefire VRT for registered users.
Repeated several times, same result.

Re: Problems update Guardian 2.0.2

Posted: December 31st, 2018, 1:49 pm
by Roberto Peña
I can´t report by Bugzilla, because is down.
Bugzilla error.jpg
Grettings and happy new year!!!.

Re: Problems update Guardian 2.0.2

Posted: December 31st, 2018, 4:01 pm
by Mentalic
Looks like there are additional problems with Guardian/intrusion detection because I experienced a number of odd things last night while trying to tune my setup.

-Intrusion detection filter check box's selections disappear by themselves yet I suspect there still active because memory load did not change.
-Altering Intrusion filter selection resulted in several "white screen" crashes.
-Guardian blocked hosts list cleared itself.
-At one point Guardian stopped blocking again, did the snort file on/off/on and it worked again.

Uninstalled Guardian last night and about to do a clean install without it until this gets sorted out.

Re: Problems update Guardian 2.0.2

Posted: January 2nd, 2019, 12:43 am
by Bradh
I am also seeing this problem on several i586 installs. Have not seen problem with any of my x86_64 installs.

I now see why I had no problems with x86_64 installs. They hadn't taken the Guardian 2.0.2 update yet. That is what breaks Guardian.

Re: Problems update Guardian 2.0.2

Posted: January 25th, 2019, 12:56 pm
by Roberto Peña
Good morning to everybody.

I am sorry to report that with the test version 127, the problem is not solved. You have to do what Mentalic says every time IPFire starts.

Greetings.

Re: Problems update Guardian 2.0.2

Posted: January 25th, 2019, 1:08 pm
by DJ-Melo
bugzilla is back online pls report a bug

Re: Problems update Guardian 2.0.2

Posted: January 25th, 2019, 1:14 pm
by Roberto Peña
Good Morning DJ-Melo.

It is already reported:

https://bugzilla.ipfire.org/show_bug.cgi?id=11954

Regards.

Re: Problems update Guardian 2.0.2

Posted: February 7th, 2019, 2:37 pm
by nazmul
Hello,

I have Guardian installed and service is running. But I cant see Guardian Interface under intrusion detection . I am using IPFire 2.21 (x86_64) - Core Update 127. I have faced the same in update 126 too. I have tried several uninstall & reinstall, but no luck.

Regards

Nazmul

Re: Problems update Guardian 2.0.2

Posted: February 10th, 2019, 3:00 am
by callifo
Same as above, 127 still has this issue present. Running IPFire 2.21 (i586) - core127